RULES
GENERAL RULES :
1-) Radio, phone, etc. radio-frequency communication devices are prohibited between the pilot and pit personel.
2-) Pilot and pit personnel are forbidden to talk with each other.
3-) Keep the materials such as fuel pump,starter box etc. in pit line is prohibited.

1/8 GAS ON ROAD CARS :
1-) The cars which race in this class should be 4 X 4.
2-) Engine volume has to be 3,50 ccm (0,21ci).
3-) Maximum carburettor diameter has to be 9mm .
4-) Fuel tank capacity has to be maximum 125 ml.
5-) Measurements from outside to outside :
6-) Wheel base : 270-330mm
7-) Width (without cap) : 267mm
8-) Maximum Back tire’s width: 64mm
9-) The diameter of the tire rims does not exceed 54 mm and also tire immobilization systems does not run over the rim in any way.
10-) The cars have to have a brake and a clutch systems .Cars should be able to start up without moving where it stops .
11-) In order to minimize the damage whether itself or another cars when a crash occur, car has to have a bumper in front of its own body . A flexible material should be preferred for bumper.
12-) If any bumper will be assembled at the behind of the car ,the bumper distant from rear axle can not be exceed 50mm including its own width.
13-) For exhaust output , a sufficient diameter can be opened to the cap and for the antenna output,10mm diameter can be opened(For the bodyposts, engine , tank flap , air filter, carburettor adjustment, transponder and the roll bar can be opened holes at adequate size).
14-) Minimum weight of the car will be 2500 gr in racing mode (with empty fuel tank and transponder being mounted).
15-) Maximum 2 servos (1 accelerator/break servo and 1 steering) can be used in cars.
17-) No Traction Tontrol System or Break Control System (ABS) can be used in cars.
18-) In transmission system there shall be maximum 2 gears.

1/10 200mm NITRO TOURING CARS :
1-) The cars which race in this class should be 4 X 4.
2-) Engine volume has to be 2.11Cm³ (0.12ci).
3-) Turbo engines are allowed and they have to max. 3 ports + exhaust.
4-) Maximum carburettor diameter has to be 5.5mm.
5-) Fuel tank capacity has to be maximum 75 ml.
6-) The measurements from outside to outside
7-) Wheel base : 230-270mm
8-) Width (without cap) :170-200mm
9-) Lenght (including cap and wing) :360-460mm
10-) Maximum height : 175mm
(to under chassis including 10mm spacer)
11-) Maximum back wheel’s width : 30 mm
12-) Maximum front wheel’s width : 26 mm
13-) Sponge or rubber tire can be use.
14-) In the tire immobilization systems there shall be used screw or nut and these screws and nuts can be run over from the rim maximum 2 mm. Quick-Change wheel change system can not be used.
15-) Cars have to have a brake and clutch systems .Car should be able to start up without moving where it stops .
16-) In order to minimize the damage whether itself or another car when a crash occur, car has to has a bumper in front of its own body . A flexible material should be preferred for bumber.
17-)The bodies to be used in racings must be touring car ones . It is prohibited to use Lemans body type.
18-) The caps to be used in the cars have to be made of flexible material and should be painted. It is forbidden to use transparent wing.
19-) The bodies can not be cut /drilled in terms of damaging other cars and distrupting its appearance and body‘s general view, Bodies should not have ledges or indentations and no exaggerated wing can be used instead of body’s standard dynamic.The wing height and width to be used has been limited to body cap height and body width.
20-) Front glass can not be cut completely. For ventilation a hole can be opened with 50 mm diameter.
21-) Sidefront and rear glasses can be cut.
22-) No Traction Control System or Break Control System (ABS) can be used in cars.
23-) For exhaust output , for antenna output ,for carburettor adjustment holes with10mm diameter can be opened to the cap.For Bodyposts and transponders a hole with adequate size can be opened.For filling the fuel tank a hole with 50 mm diameter can be opened to ceiling. The center of the fuel hole should be placed on fuel flap exactly. Fuel hole can be fixed to front glass but if already a ventilation hole exists on front glass there should be at least 5 mm distance between them. A sparkplug tongs on cooling head on the ceiling of car and with respect to change sparkplug a hole with 35 mm maximum can be drilled.There is not any other hole nearby this hole 5 mm distance. If the hole to be drilled for ventilation at front glass is that to be used for fuel at the same time ,diameter of this hole has to be 50 mm at maximum and no fuel hole to ceiling can be drilled in this case .
24-) Minimum weight of the vehicle shall be 1.700 gr. (with empty fuel tank and with transponder being mounted).
25-) Maximum 2 servo-assistance (1 accelerator/break servo and 1 steering) can be used in vehicles.
26-) In transmission system there shall be maximum 2 gears
27-) Roll bar shall definitely remain inside the cabin